Error
code
Module
Type
Brief Description
10014
Error
获取调压Information失败
Communication Failure to get pressure regulator
information
Error Description
Recommended measures
1.通过 过 件左下角的过 接状过 过 ，过 过 过 过 是否过 接正常。
可能1.打印软件与设备通信异常
可能2.主板未正常运行
2.过 件版本Information里过 看过 件和主板程序的前四位版本号是否相等。过 看固件
是否正确。
1. Check whether the device is connected properly through the connection status
Possible 1. Abnormal communication between the diagram in the lower left corner of the software.
printing software and the printer
2. Check whether the first four digits of the software and mainboard program version
Possible 2. The mainboard is not running normally numbers are equal in the software version information. Check whether the firmware is
correct.
10015
Error
打印失败，发送打印数据失败
Communication Failed to print, failed to send
printing data
1.通过 过 件左下角的过 接状过 过 ，过 过 过 过 是否过 接正常。
可能1.打印软件与主板通信异常
2.过 件版本Information里过 看过 件和主板程序的前四位版本号是否相等。过 看固件
是否正确。
可能2.主板未正常运行
1. Check whether the device is connected properly through the connection status
Possible 1. Abnormal communication between the diagram in the lower left corner of the software.
printing software and the mainboard
2. Check whether the first four digits of the software and mainboard program version
Possible 2. The mainboard is not running normally numbers are equal in the software version information. Check whether the firmware is
correct.
10016
Error
打印失败，发送打印Information
Communication
失败
Failed to print, failed to send print
message
1.通过 过 件左下角的过 接状过 过 ，过 过 过 过 是否过 接正常。
可能1.打印软件与主板通信异常
2.过 件版本Information里过 看过 件和主板程序的前四位版本号是否相等。过 看固件
是否正确。
可能2.主板未正常运行
1. Check whether the device is connected properly through the connection status
Possible 1. Abnormal communication between the diagram in the lower left corner of the software.
printing software and the mainboard
2. Check whether the first four digits of the software and mainboard program version
Possible 2. The mainboard is not running normally numbers are equal in the software version information. Check whether the firmware is
correct.
10017
Error
可能1.固件配置或固件参数不正确或破损坏
等待获取马达光栅精度或计算X
齿轮比动作启动超时
可能2.打印软件与主板通信异常
可能3.主板未正常运行
Possible 1. The firmware configuration or
Communication Wait to get motor raster accuracy or firmware parameters are incorrect or damaged.
calculate X-gear ratio action start Possible 2. The communication between the
timeout
printing software and the mainboard is abnormal.
Possible 3. The mainboard is not operating
normally.
1.重新过 入正确的固件配置和固件参数文件
2.通过 过 件左下角的过 接状过 过 ，过 过 过 过 是否过 接正常。
3.过 件版本Information里过 看过 件和主板程序的前四位版本号是否相等。过 看固件
是否正确。
1. Re-import the correct firmware configuration and firmware parameter file
2. Check whether the device is connected properly through the connection status
diagram in the lower left corner of the software.
3. Check whether the first four digits of the software and mainboard program version
numbers are equal in the software version information. Check whether the firmware is
correct.
    "